View MT88E39AS_1106087.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MT88E39 Calling Number Identification Circuit
(CNIC1.1) Data Sheet Features
* * * * * * * * * * 1200 baud Bell 202 and CCITT V.23 Frequency Shift Keying (FSK) demodulation Compatible with Bellcore GR-30-CORE, SR-TSV002476, TIA/EIA-716 and ETSI 300 778-1 High input sensitivity Dual mode 3-wire data interface (Serial FSK data stream or MT88E43 compatible 1 byte buffer) Internal gain adjustable amplifier Carrier detect status output Uses 3.579545 MHz crystal or ceramic resonator 3 to 5 V 10% supply voltage Low power CMOS with power down mode Direct pin to pin replacement of MT8841 and MT88E41
Ordering Information MT88E39AS MT88E39ASR MT88E39AS1 MT88E39ASR1 16 16 16 16 Pin Pin Pin Pin SOIC SOIC SOIC* SOIC* Tubes Tape & Reel Tubes Tape & Reel
November 2004
*Pb Free Matte Tin -40C to +85C
Description
The MT88E39 Calling Number Identification Circuit (CNIC1.1) is a CMOS integrated circuit which provides an interface to calling line information delivery services that utilize 1200 baud Bell 202 or CCITT V.23 FSK data transmission schemes. The MT88E39 receives and demodulates the FSK signal and outputs the data into a simple dual mode 3-wire serial interface which eliminates the need for an UART. The MT88E39 is Bellcore, ETSI and NTT compatible and can operate in 3 V and 5 V applications. It is a pin to pin replacement of the MT8841 and MT88E41 by operating in the MT88E41 FSK interface mode (mode 0) when placed in a MT88E41 socket. New designs may also choose the MT88E43 compatible interface (mode 1) where the microcontroller reads the FSK byte from a 1 byte buffer.
Applications
* Global (North America, Japan, Europe) FSK based CID (Calling Identity Delivery) / CLIP (Calling Line Identity Presentation) Feature phones, adjunct boxes FAX machines Telephone answering machines Computer Telephony Integration (CTI) Battery powered applications
* * * * *
GS ININ+ + Receive Bandpass Filter FSK Demodulator Data and Timing Recovery
DATA DR DCLK
CAP VRef Bias Generator Carrier Detector CD
Clock Generator
to other circuits
PWDN
OSC1 OSC2
MODE
IC
Figure 1 - Functional Block Diagram 1
Zarlink Semiconductor Inc. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 1998 - 2004, Zarlink Semiconductor Inc. All Rights Reserved.
MT88E39
Data Sheet
IN+ INGS VRef CAP OSC1 OSC2 VSS
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9 16 PIN SOIC
VDD IC** MODE* PWDN CD DR DATA DCLK * Was IC1 in MT88E41 ** Was IC2 in MT88E41
Figure 2 - Pin Connections Pin Description Pin # 1 2 3 4 5 6 7 8 9 Name IN+ INGS VRef CAP Non-inverting Op-Amp (Input). Inverting Op-Amp (Input). Gain Select (Output). Gives access to op-amp output for connection of feedback resistor. Voltage Reference (Output). Nominally VDD/2. This is used to bias the op-amp inputs. Capacitor. Connect a 0.1 F capacitor to VSS. Description
OSC1 Oscillator (Input). Crystal connection. This pin can be driven directly from an external clocking source. OSC2 Oscillator (Output). Crystal connection. When OSC1 is driven by an external clock, this pin should be left open. VSS Power supply ground. DCLK 3-wire FSK Interface: Data Clock (CMOS Output/Schmitt Input). In mode 0 (MT88E41 compatible mode - when the MODE pin is logic low) this is a CMOS output which denotes the nominal mid-point of a FSK data bit. In mode 1 (when the MODE pin is logic high) this is a Schmitt trigger input used to shift the FSK data byte out to the DATA pin. DATA 3-wire FSK Interface: Data (CMOS Output). In mode 0 (MT88E41 compatible mode - when the MODE pin is logic low) the FSK serial bit stream is output to DATA as demodulated. Mark frequency corresponds to logical 1. Space frequency corresponds to logical 0. In mode 1 (when the MODE pin is logic high) the start and stop bits are stripped off and only the data byte is stored in a 1 byte buffer. At the end of each word signalled by the DR pin, the microcontroller should shift the byte out to DATA pin by applying 8 read pulses at the DCLK pin. DR 3-wire FSK Interface: Data Ready (Open Drain/CMOS Output). Active low. In mode 0 (MT88E41 compatible mode - when the MODE pin is logic low) this is an open drain output. In mode 1 (when the MODE pin is logic high) this is a CMOS output. This pin denotes the end of a word. Typically, DR is used to interrupt the microcontroller. It is normally hi-Z or high (modes 0 and 1 respectively) and goes low for half a bit time at the end of a word. But in mode 1 if DCLK begins during DR low, the first rising edge of the DCLK input will return DR to high. This feature allows an interrupt requested by DR to be cleared upon reading the first DATA bit.
10
11
2
Zarlink Semiconductor Inc.
MT88E39
Pin Description Pin # 12 Name CD Description
Data Sheet
Carrier Detect (Open Drain/CMOS Output). Active low. In mode 0 (MT88E41 compatible mode - when the MODE pin is logic low) this is an open drain output. In mode 1 (when the MODE pin is logic high) this is a CMOS output. A logic low indicates that a carrier has been present for a specified time on the line. A time hysteresis is provided to allow for momentary discontinuity of carrier. The demodulated FSK data is inhibited until the carrier has been detected.
13 14
PWDN Power Down (Schmitt Input). Active high. Powers down the device including the input opamp and the oscillator. Must be low for operation. MODE Mode select (Input). This pin selects the 3-wire FSK interface mode. To select mode 0 (MT88E41 compatible mode) this pin should be logic low. To select mode 1 this pin should be logic high. Because this pin is already connected to Vss in 'E41 applications, the MT88E39 can replace the 'E41 without any circuit or software change. IC VDD Internal Connection. Internal connection. Leave open circuit. In MT88E41, this was IC2 which was also left open in the application circuit. Positive power supply voltage.
15 16
Functional Description
The MT88E39 is a FSK demodulator compatible with FSK based Caller ID services around the world, such as in North America, France, Germany, and Japan. Caller ID is the generic term for a group of services offered by telephone operating companies whereby information about the calling party is delivered to the subscriber. In the FSK based methods, the information is modulated in either Bell 202 (in North America) or CCITT V.23 (in Europe) FSK format and transmitted at 1200 baud from the serving end office to the subscriber's terminal. In North America, Caller ID uses the voiceband data transmission interface defined in the Bellcore document GR30-CORE. The terminal or CPE (Customer Premises Equipment) requirements are defined in Bellcore document SR-TSV-002476. Typical services are CND (Calling Number Delivery), CNAM (Calling Name Delivery), VMWI (Visual Message Waiting Indicator) and CIDCW (Calling Identity Delivery on Call Waiting). In on-hook Caller ID, such as CND and CNAM, the information is typically transmitted from the end office before the subscriber picks up the phone. There are various methods such as between the first and second rings (North America), between an abbreviated ring and the first true ring (Japan, France and Germany). On-hook Caller ID can also occur without ringing for services such as VMWI. The MT88E39 is suitable for these forms of alerting. In off-hook Caller ID, such as CIDCW, information about a new calling party is sent to the subscriber who is already engaged in a call. Bellcore's method uses a special dual tone known as CAS (CPE Alerting Signal) which should be detected by the CPE. After the CPE has acknowledged with a DTMF digit, the end office will send the FSK data. The MT88E39 is suitable for receiving the FSK data but a separate CAS detector is required. The MT88E39 provides an interface to the Caller ID physical layer. It bandpass filters and demodulates the 1200 baud FSK signal. It also provides a convenient interface to extract the demodulated FSK data. Although the main application of the MT88E39 is Caller ID, it can also be used wherever 1200 baud Bell 202 and/or CCITT V.23 FSK reception is required. 3 to 5V operation The MT88E39 can operate from 5.5 V down to 2.7 V, but the FSK reject level will change with Vdd. In a battery powered CPE, the FSK accept level will become lower as the batteries are run down. If the CPE is designed for 4.5 V, the accept level will be lowered when the batteries drain to 3 V. In North America there is a requirement for rejecting FSK signals which are below 3 mVrms when data is not preceded by ringing, such as VMWI (Visual
3
Zarlink Semiconductor Inc.
MT88E39
Data Sheet
Message Waiting Indicator) applications. When the batteries are drained, the CPE will not meet the reject level. For on-hook Caller ID, there is no reject level and the CPE will meet all requirements. Input Configuration The input arrangement of the MT88E39 provides an operational amplifier, as well as a bias source (VRef) which is used to bias the inputs at VDD/2. Provision is made for connection of a feedback resistor to the op-amp output (GS) for adjustment of gain. Figure 3 shows the necessary connections for a differential input configuration. In a single-ended configuration, the input pins are connected as shown in Figure 4.
C1
R1
IN+ IN-
C2
R4
R5 GS R3 R2
VRef
DIFFERENTIAL INPUT AMPLIFIER MT88E39 C1 = C2 R1 = R4 R3 = (R2 x R5) / (R2 + R5) For unity gain, R5 = R1 INPUT IMPEDANCE VOLTAGE GAIN (AVdiff) = R5/R1 (ZINdiff) = 2 R12 + (1/C)2
Figure 3 - Differential Input Configuration
IN+
C
RIN
IN-
RF
GS
VOLTAGE GAIN (AV) = RF / RIN
VRef
MT88E39
Figure 4 - Single-Ended Input Configuration 3-wire FSK Data Interface The MT88E39 provides a powerful dual mode 3-wire interface so that the 8-bit data words in the demodulated FSK bit stream can be extracted without the need either for an external UART or for the microcontroller to perform the UART function in software. The interface is specifically designed for the 1200 baud rate and is comprised of the DATA, DCLK (data clock) and DR (data ready) pins. Two modes (0 and 1) are selectable via control of the device's MODE pin. In mode 0 the FSK bit stream is output as demodulated. In mode 1 the FSK data byte is store in a 1 byte buffer. Note that in mode 0 DR and CD are open drain outputs; in mode 1 they are CMOS outputs. DCLK is an output in mode 0, an input in mode 1.
4
Zarlink Semiconductor Inc.
MT88E39
Mode 0
Data Sheet
This mode is selected when the MODE pin is low. It is the MT88E41 compatible mode where the FSK data stream is output as demodulated. Since the MODE pin was IC1 in MT88E41 and connected to Vss, the MT88E39 will work in mode 0 when placed in a MT88E41 socket. In this mode, the MT88E39 receives the FSK signal, demodulates it, and outputs the data directly to the DATA pin (see Figure 11). For each received stop and start bit sequence, the MT88E39 outputs a fixed frequency clock string of 8 pulses at the DCLK pin. Each DCLK rising edge occurs in the nominal centre of a data bit. DCLK is not generated for the stop and start bits. Consequently, DCLK will clock only valid data into a peripheral device such as a serial to parallel shift register or a microcontroller. The MT88E39 also outputs an end of word pulse (Data Ready) on the DR pin, which indicates the reception of every 10-bit word (counting the start and stop bits) sent from the end office. DR can be used to interrupt a microcontroller or cause a serial to parallel converter to parallel load its data into a microcontroller. The mode 0 DATA pin can also be connected to a personal computer's serial communication port after converting from CMOS to RS-232 voltage levels. Mode 1 This mode is selected when the MODE pin is high. In this mode, the microcontroller supplies read pulses at the DCLK pin (which is now an input) to shift the 8-bit data words out of the MT88E39, onto the DATA pin. The MT88E39 asserts DR to denote the word boundary and indicate to the microprocessor that a new word has become available (see Figure 12). Internal to the MT88E39, the demodulated data bits are sampled and stored. The start and stop bits are stripped off. After the 8th bit, the data byte is parallel loaded into an 8 bit shift register and DR goes low. The shift register's contents are shifted out to the DATA pin on the supplied DCLK's rising edge in the order they were received. If DCLK begins while DR is low, DR will return to high upon the first DCLK. This feature allows the associated interrupt to be cleared by the first read pulse. Otherwise DR is low for half a nominal bit time (1/2400 sec). After the last bit has been read, additional DCLKs are ignored. Note that in both modes, the 3-pin interface may also output data generated by speech or other voiceband signals. The user may choose to ignore these outputs when FSK data is not expected, or force the MT88E39 into its power down mode. Power Down Mode For applications requiring reduced power consumption, the MT88E39 can be forced into power down when it is not needed. This is done by pulling the PWDN pin high. In power down mode, the oscillator, op-amp and internal circuitry are all disabled and the MT88E39 will not react to the input signal. DR and CD are at high impedance or at logic high (modes 0 and 1 respectively). In mode 0, DATA and DCLK are at logic high. The MT88E39 can be awakened for reception of the FSK signal by pulling the PWDN pin low. Carrier Detect The carrier detector provides an indication of the presence of a signal in the FSK frequency band. It detects the presence of a signal of sufficient amplitude at the output of the FSK bandpass filter. The signal is qualified by a digital algorithm before the CD output is set low to indicate carrier detection. A 10ms hysteresis is provided to allow for momentary signal drop out once CD has been activated. CD is released when there is no activity at the FSK bandpass filter output for 10 ms. When CD is inactive (high), the raw output of the demodulator is ignored by the data timing recovery circuit (see Figure 1). In mode 0, the DATA pin is forced high. No DCLK or DR signal is generated. In mode 1, the internal shift register is not updated and no DR is generated. If DCLK is clocked (in mode 1), DATA is undefined. Note that signals such as CAS, speech and DTMF tones also lie in the FSK frequency band and the carrier detector may be activated by these signals. They will be demodulated and presented as data. To avoid false data, the PWDN pin should be used to disable the FSK demodulator when no FSK signal is expected.
5
Zarlink Semiconductor Inc.
MT88E39
Ringing, on the other hand, does not pose a problem as it is ignored by the carrier detector. Crystal Oscillator
Data Sheet
The MT88E39 uses either a 3.579545 MHz ceramic resonator or crystal oscillator as the master timing source. The crystal specification is as follows: Frequency: 3.579545 MHz Frequency tolerance: 0.2%(-40C+85C) Resonance mode: Parallel Load capacitance: 18 pF Maximum series resistance: 150 ohms Maximum drive level (mW): 2 mW e.g., CTS MP036S
MT88E39 OSC1 OSC2
MT88E39 OSC1 OSC2
MT88E39 OSC1 OSC2
3.579545 MHz
to the next MT88E39
(For 5 V application only) Figure 5 - Common Crystal Connection For 5 V applications any number of MT88E39 devices can be connected as shown in Figure 5 such that only one crystal is required. The connection between OSC2 and OSC1 can be DC coupled as shown, or the OSC1 input on all devices can be driven from a CMOS buffer (dc coupled) with the OSC2 outputs left unconnected. VRef and CAP Inputs VRef is the output of a low impedance voltage source equal to VDD/2 and is used to bias the input op-amp. A 0.1 F capacitor is required between CAP and VSS to suppress noise on VRef.
Applications
Table 1 shows the Bellcore and ETSI FSK signal characteristics. The application circuit in Figure 6 will meet these requirements. For 5 V designs the input op-amp should be set to unity gain to meet the Bellcore requirements and -2.5 dB gain for ETSI requirements. As supply voltage (VDD) is decreased, the FSK detect threshold will be lowered. Therefore for designs operating at other than 5 V nominal voltage, to meet the FSK reject level requirement the gain of the op-amp should be reduced accordingly. For 3 V designs the gain settings for Bellcore and ETSI should be -3 dB and -5.5 dB respectively. For applications requiring detection of lower FSK signal level, the input op-amp may be configured to provide adequate gain. However, too much gain will cause noise tolerance to fail the TIA requirements because the FSK signal will be clipped at GS when the single tone noise is added.
6
Zarlink Semiconductor Inc.
MT88E39
Vdd R2 MT88E39 IN+ Vdd
RING
Data Sheet
Vdd
TIP
C1
R1
D1 D2
100 nF 20% VDD IC
Vdd
Vdd R9*1
C2
R3
D3 D4
R4
R5 R6
R7
INGS VRef CAP
MODE PWDN CD DR DATA DCLK
R8*1
100 nF 20% D5 D7 D6 D8
1N5231B
OSC1 Xtal OSC2 VSS
100 nF 10% 50 V
(FSK interface mode 0 selected) Vdd = To microcontroller = From microcontroller 200 K 5% Motorola 4N25 464 K 5% (Ring Detect) 10 nF To microcontroller
330 nF R10 10% 250 V
Note: *1 R8 and R9 not required when FSK interface mode 1 is selected. Unless stated otherwise, resistors are 1%, 0.1 Watt; capacitors are 5%, 6.3 V D1, D2, D3, D4 = diodes, 1N4003 or 1N4148 or equivalent D5, D6, D7, D8 = bridge rectifier diodes, 1N914 Xtal = 3.579545 MHz, +/-0.2% R8 = R9 = 100 K, 20% R10 = 12K1, 1W5, 5%, Fusible resistor R2 = R4 = 34 K For 1000 Vrms, 60 Hz isolation from Tip to Earth and Ring to Earth: R1 = R3 = 430 K, 0.5 W, 5%, 475 V minimum. e.g., IRC Type GS-3 C1 = C2 = 2 n2, 1332 V minimum If the 1000Vrms is met by other means, then this circuit has to meet FCC part 68 Type B Ringing: R1 = R3 = 432 K, 0.1 W, 1%, 56 V minimum C1 = C2 = 2n2, 212V minimum Example of component values for Vdd = 5 V +/- 10% For Bellcore applications, set input gain = 0 dB: For ETSI applications, set input gain = -2.5 dB: R5 = 53K6 R5 = 53K6 R6 = 60K4 R6 = 63K4 R7 = 464K R7 = 348K Example of component values for Vdd = 3 V +/- 10% For Bellcore applications, set input gain = -3 dB: For ETSI applications, set input gain = -5.5 dB: R5 = 44K2 R5 = 44K2 R6 = 51K1 R6 = 53K6 R7 = 332K R7 = 249K
Figure 6 - Application Circuit
7
Zarlink Semiconductor Inc.
MT88E39
Parameter Mark (logical 1) frequency Space (logical 0) frequency Received signal level Reject signal level Transmission rate Twist Signal to noise ratio North America: Bellcore *1 1200 Hz +/- 1% 2200 Hz +/- 1% -36.20 to -4.23 dBm (12 to 476 mVrms)
*3
Data Sheet
Europe: ETSI *2 1300 Hz +/- 1.5% 2100 Hz +/- 1.5% -33.78 to -5.78 dBm (-36 to -8 dBV *4) *5 -47.78 dBm (-50 dBV) 1200 baud +/- 1% -6 to +6 dB
-48.23 dBm (3 mVrms) (VMWI only) 1200 baud +/- 1% -6 to +10 dB Single tone (f): -18 dB (f<=60 Hz) -12 dB (60=3200 Hz) 0 dB
>= 25 db (300 to 3400 Hz)
MT88E39 FSK input gain for Vdd = 5 V +/-10%
Note: *1: *2: *3: *4: *5:
-2.5 dB
Table 1 - FSK signal characteristics specified by some standard bodies
Recommended by TIA/EIA-716. Bellcore has agreed to the values and will incorporate them into its future standards. ETS 300 778-1 (On-hook) Sep 97, ETS 300 778-2 (Off-hook) Jan 97. dBm = Decibels above or below a reference power of 1 mW into 600 ohms. 0 dBm = 0.7746 Vrms. dBV = Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms. On-hook signal range. The Off-hook signal levels are inside this range: -30.78 to -7.78 dBm. Vdd Interrupt Source 1 INT1 (open drain) R1 can be opened and D1 shorted if the microcontroller does not read the INT1 pin. Interrupt Source 2 INT2 (CMOS) INT (input) Vdd MT88E39 DR (Mode 0: Open Drain) (Mode 1: CMOS Input Port Bit *R2 can be omitted if mode 1 is selected R2 * R1 D1 Vdd Microcontroller
Figure 7 - Application Circuit (multiple interrupt source)
8
Zarlink Semiconductor Inc.
MT88E39
Absolute Maximum Ratings* - Voltages are with respect to VSS unless otherwise stated. Parameter 1 2 3 4 5 DC Power Supply Voltage VDD to VSS Voltage on any pin Current at any pin (except VDD and VSS) Storage Temperature Package Power Dissipation Symbol VDD VP I I/O TST PD -65 Min. -0.3 -0.3 Max. 6
Data Sheet
Units V V mA C mW
VDD+0.3 10 +150 500
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated. Characteristics 1 DC Power Supply Voltage 2 Clock Frequency 3 Tolerance on Clock Frequency 4 Operating Temperature DC Electrical Characteristics Characteristics 1 2
S U P P L Y DR, CD, DATA, DCLK
Sym. VDD fOSC fc
Min. 2.7
Typ. 3.579545
Max. 5.5 0.2
Units V MHz % C
Test Conditions
-40
+85
Sym. IDDQ IDD
Min.
Typ.* 0.1 1.2 1.9
Max. 15 2.0 3.0
Units A mA mA mA mA
Test Conditions Notes* 1 Notes* 2
Standby Supply Current Operating Supply Current VDD = 3.0 V, 25oC VDD = 5.0 V, 25oC Sink Current Source current DATA DCLK (in mode 0) DR, CD (in mode 1) Output hi-Z current (in mode 0) Schmitt Input High Threshold Schmitt Input Low Threshold Schmitt Hysteresis CMOS Input High Voltage CMOS Input Low Voltage Input Current Output Voltage Output Resistance
3 4
IOL IOH
2.5 0.8
VOL = 0.1 VDD VOH = 0.9 VDD
5 6
DR, CD
IOZ VT+ VTVHYS VIH VIL IIN VRef 0.5*VDD - 0.1 RRef 0.48*VDD 0.28*VDD 0.2 0.7*VDD VSS
10 0.68*VDD 0.48*VDD
A V V V
VOZ=VSS to VDD
7 8 9 10 11
PWDN, DCLK (in mode 1) MODE PWDN, DCLK, MODE VRef
VDD 0.3*VDD 10 0.5*VDD + 0.1 2
V A V k VSS VIN VDD No Load
DC Electrical Characteristics are over recommended operating conditions unless otherwise stated. * Typical figures are at 25C and are for design aid only. Note 1: Note 2: PWDN = Vdd. FSK input = 0 mVrms. Digital inputs at either Vdd or Vss. No current drawn from output pins. PWDN = Vss. FSK input = 0 mVrms. With no current drawn from Vref, OSC2 and all digital pins.
9
Zarlink Semiconductor Inc.
MT88E39
Electrical Characteristics - Gain Setting Amplifier Characteristics 1 2 3 4 5 6 7 8 9 Input Leakage Current Input Resistance Input Offset Voltage Power Supply Rejection Ratio Common Mode Rejection DC Open Loop Voltage Gain Unity Gain Bandwidth Output Voltage Swing Capacitive Load (GS) Sym. IIN Rin VOS PSRR CMRR AVOL fC VO CL RL VCM 100 1.0
VDD-1.0
Data Sheet
Min.
Typ.
Max. 1
Units A M
Test Conditions VSS VIN VDD
5 25 30 30 40 0.2 0.5
VDD-0.7
mV dB dB dB MHz V pF k V Load 100 k 1 kHz ripple on VDD VCMmin VIN VCMmax
50
10 Resistive Load (GS) 11 Common Mode Voltage Range
Electrical characteristics are over recommended operating conditions, unless otherwise stated. Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing.
AC Electrical Characteristics - FSK Characteristics 1 Input Detection Level Sym. Min. -37.78 -40 10 1188 1188 2178 1200 1200 2200 Typ. Max. -1.78 -4 631 1212 1212 2222 Units dBm 1, 2, 3, 4 dBV mVrms baud Hz Hz Hz Hz dB 10 dB 3, 4, 5 6 Notes*
2 Input Baud Rate 3 Input Frequency Detection Bell 202 1 (Mark) Bell 202 0 (Space) CCITT V.23 1 (Mark) CCITT V.23 0 (Space) 4 Input Noise Tolerance 20 log 5 Twist=20 log(VMark ) V
Space
1280.5 1300 1319.5 2068.5 2100 2131.5 SNR 20 -6
AC Electrical Characteristics are over recommended operating conditions, unless otherwise stated. Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. Notes*: 1. dBm = Decibels above or below a reference power of 1 mW into 600 . 0 dBm = 0.7746 Vrms. 2. dBV = Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms. 3. Input op-amp configured to 0 dB gain at Vdd = 5 V+/-10%, -3 dB at Vdd = 3 V+/-10%. 4. Mark and Space frequencies have the same amplitude. 5. Band limited random noise (200-3400 Hz). Present when FSK signal present. 6. OSC1 at 3.579545 MHz 0.2%.
10
Zarlink Semiconductor Inc.
MT88E39
AC Electrical Characteristics - Timing Characteristics 1 2 3 4 5
CD PWDN OSC1
Data Sheet
Sym. tPU tPD tIAL tIAH
Min.
Typ.
Max. 50
Units ms s ms ms ms 1
Notes*
Power-up time Power-down time Input FSK to CD low delay Input FSK to CD high delay Hysteresis
100
1000 25
10 10
AC Electrical Characteristics are over recommended operating conditions unless otherwise stated. Typical figures are at 25C and are for design aid only, not guaranteed and not subject to production testing. Notes*: 1. The device will stop functioning within this time, but more time may be required to reach IDDQ.
AC Electrical Characteristics - 3-Wire FSK Interface Timing (Mode 0) Characteristics 1 2 3 4 5 6 7 8 9 10 11 12 13
DR DCLK DR DCLK DATA DCLK DATA
Sym.
Min. 1188
Typ. 1200 1
Max. 1212 5 200 200
Units. bps ms ns ns s s 3 3 1, 6
Notes*
Rate Input FSK to DATA delay Rise time Fall time DATA to DCLK delay DCLK to DATA delay Frequency High time Low time DCLK to DR delay Rise time Fall time Low time tCH tCL tCRD tRR tFF tRL tIDD tR tF tDCD tCDD
6 6 1200.4 415 415 415
416 416 1202.8 416 416 416 1205.2 417 417 417 10 200
1, 2, 5, 6 1, 2, 5, 6 2 2 2 2 4 4 2
Hz s s s s ns s
415
416
417
AC Electrical Characteristics are over recommended operating conditions unless otherwise stated. Typical figures are at 25C and are for design aid only, not guaranteed and not subject to production testing. Notes*: 1. FSK input data at 1200 12 baud. 2. OSC1 at 3.579545 MHz 0.2%. 3. 10 k to V SS, 50pF to V SS. 4. 10 k to V DD, 50pF to V SS. 5. Function of signal condition. 6. For a repeating mark space sequence, the data stream will typically have equal 1 and 0 bit durations.
11
Zarlink Semiconductor Inc.
MT88E39
AC Electrical Characteristics - 3-Wire FSK Interface Timing (Mode 1) Characteristics 1 2 3 4 5
DCLK DR DCLK
Data Sheet
Sym. fDCLK1
Min.
Typ.
Max. 1
Units MHz % ns ns ns
Notes* See Fig. 12
Frequency Duty Cycle Rise Time DCLK low setup time to DR DCLK low hold time to DR
30
70 100
tDDS tDDH
500 500
See Fig. 12 See Fig. 12
AC Electrical Characteristics are over recommended operating conditions unless otherwise stated. Typical figures are at 25C and are for design aid only, not guaranteed and not subject to production testing.
tR DATA
tDCD
tCDD
tF
DCLK tCL tR tCH tF
Figure 8 - DATA and DCLK Output Timing (Mode 0)
tFF DR tRL
tRR
Figure 9 - DR Output Timing (Mode 0)
12
Zarlink Semiconductor Inc.
MT88E39
2 sec TIP/RING First Ring 500 ms (min) Data 200 ms (min) channel seizure Mark state checksum
Data Sheet
Input FSK
Second Ring
PWDN
tPU tPD OSC2
CD *
tIAL
tIAH
DATA High (Input Idle) High (Input Idle)
DCLK (mode 0)
DR * * with pull-up resistor in mode 0
Figure 10 - Input and Output Timing (Bellcore CND Service)
start stop TIP/RING b7 tIDD start DATA b7 stop b0 b1 b2 b3 b4 b5 b6 b7 stop start b0 b1 b2 b3 b4 b5 b6 b7 stop start b0 b1 b2 1 0 b0 b1 b2 b3 b4 b5 b6 b7 start stop 1 0 b0 b1 b2 b3 b4 b5 b6 b7 start stop 1 0 b0 b1 b2
DCLK tCRD DR * * with external pull-up resistor
Figure 11 - Serial Data Interface Timing (Mode 0)
13
Zarlink Semiconductor Inc.
MT88E39
Data Sheet
Demodulated Data (Internal Signal)
word N 7 stop start 0 1 2
word N+1 3 4 5 6 tRL 7 stop
DR (Data Ready) CMOS tDDS Output tDDH DCLK (Data Clock)* Schmitt Input DATA Output 6 7
1/fDCLK1
0
1
2
3 word N
4
5
6
7
0
word N-1
* The DCLK input must be low before and after DR falling edge DCLK clears DR DCLK does not clear DR, so DR is low for maximum time (1/2 bit time)
Figure 12 - Serial Data Interface Timing (Mode 1)
14
Zarlink Semiconductor Inc.
For more information about all Zarlink products visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request.
Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE

▲Up To Search▲

Price & Availability of MT88E39AS

	To Download MT88E39AS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .